search

Ella EW-SS-A-STD Guide d'installation Page 14

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 48
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 13
www.ellasbubbles.com Page 14 0 8/14
®
www.bciacrylic.com
37
INSTALLATION / WALL SURROUNDS
TOOLS
o Orbital Jigsaw with Bosch T101 Blade
or 10 to 12 Tooth-per-inch Wood Blade
o Level
o Screwdriver
o Suction Cup
o Large and Small Wall Templates
o Utility Knife
o Sharpie
®
Marker
o Notepad
o Tape Measure
o Hammer
o Chisel
o Pipe Wrench
o Handle Puller
o Work Table
o Extension Cords
o Vacuum
o Broom and Dust Pan
o Garbage Bags
o Drywall and Screws
o Pliers
o Tub Template
o Drop Cloths
SEQUENCE OF INSTALLATION:
Wall prep rst,then install the ceiling panel, then the soap dish wall. Next step is the two side walls
and then the bathliner.
Tip:
It is recommended to install the wall surrounds rst and then the bathliner. If you wish to install the bathliner rst, please refer to page 11
for proper instructions.
Tip:
If you need to replace the mixer valve, check the codes in the city where you are working. It is quite possible that a plumber may have
to do this work.
A B C
Step 1: Remove the hardware.
Step 2: Take off the plumbing xtures and accessories, which includes the faucet, showerhead, shower grab bars, soap dish and any other xtures. DO
NOT remove the overow cover. It will be removed later.
(Image A)
Step 3: If the existing tile does not go all the way to the ceiling, pad out the existing wall above the tile to ensure the wall is ush.
Tip:
Keep ¼” and ½” drywall sheets in your vehicle.
Step 4: To pad the wall, start by measuring the section of the wall that needs to be built-out. Transfer the measurements to the drywall, then cut the drywall
according to your measurements.
Step 5: Add silicone to the back of the drywall, then press it onto the existing wall. Screw the drywall onto the existing wall to keep it secure.
(Image B)
Tip:
Though drywall is the recommended way to repair a damaged wall, you may need to add additional layers of butyl tape to r out the wall
ush to the existing tile. Please note butyl tape is 1/8” thick, so you will need to assess the proper amount needed to ll the space. Layer the
tape one strip on top of another as needed. Pull the release paper as you layer, until you have the exact thickness.
Step 6: Clean the existing wall and tub system with industrial strength cleaner and denatured alcohol. Remove all of the old caulk around the perimeter of
the bathtub using a safety scraper.
(Image C)
WALL PREP
INSTALLATION / WALL SURROUNDS
Wall Surrounds
Vue de la page 13
1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 47 48

Commentaires sur ces manuels

Pas de commentaire
  • Boris FX Goodson Imports Nature Power Akku-chek Horizon
  • Asus Stations d'accueil pour appareils mobiles Fujifilm Ampoules infrarouges Royal Sovereign Climatiseurs mobiles Tripp Lite Câbles à fibres optiques Hampton Bay Ventilateurs des ménages
  • Sony NWZ-A15 Oki 86 Philips HP4983/00 Sharp LC-32LB261U Pfister F-049-LDKK
  • Oki 5150 Manuel de l'utilisateur Sony MHC-GT111 Manuel de l'utilisateur Plustek OpticBook 3800 Manuel de l'utilisateur Brother HL 5370DW Manuel de l'utilisateur Samsung 510M Manuel de l'utilisateur